Material Lifts

The Atlantic Material Lifts are a holeless design with a side mounted hydraulic cylinder(s). Unlike conventional hydraulic systems, this design does not seep oil, making it one of the most environmentally friendly systems available. Material Lifts are governed by ASME A17.1 / CSA B44 (elevator codes) allowing for 5m/16’5” of travel distance (7.6m/ 25 ft. travel distance in Ontario, Canada). Maximum allowable lift speed is .15m/sec. (30ft./min)

The power unit and controller are located in a machine space that is adjacent to the hoistway.

Structure: The car is a welded structural steel assembly with a nonskid checker plate surface. The wall panels are constructed of sheet metal on a structural tube frame and are a minimum of 2 meters high. The car assembly is guided by high tensile “I” beam vertical guide rails by means of 16 four inch, high speed, sealed bearings attached to the top and bottom of the car. This design provides for the highest stability and least distortion available in the industry today, providing a safe and durable system for both front and side loading. Safety maintenance pins are provided when put in place, will safely support the car during maintenance or service. Atlantic’s in-house welding shop and field service team are CWB approved CSA W47.1 and W59.

The Hydraulic System: The pumping unit is comprised of a direct coupled motor and fully submerged pump, oil reservoir, suction and filler strainers, solenoid operated lowering valve, pressure gauge with isolating valve, pressure relief value, manual shut-off valve, and a manual lowering bypass valve to allow lowering of the car in the event of a power failure. The hydraulic control valve provides for soft starts and stops (optional pressure compensated flow control valve).

Our leak proof system is above ground and does not endanger surrounding soil with contamination. The hydraulic cylinder(s) is a single speed, piston seal or displacement type with seamless tube, micro-honed cylinder walls and hard chrome finish piston rods. The cylinder(s) comes equipped with a safety velocity fuse at the pressure port to stop downward motion of the car in the event of a hydraulic supply line failure.

Synchronized telescopic cylinder(s) are available for low overhead applications.

The Electrical Control System: The control panel is comprised of two main contactors inline with thermal overload motor protection, a transformer to reduce the primary voltage to 120 volts secondary for operator safety and a fused circuit of industrial relays.

The up, down push button controls are constant pressure (CPPB) type that, when depressed, will raise or lower the lift until released or the landing selected is reached. The controls and equipment may be protected against unauthorized use by key switches. The control stations are provided with an emergency stop button when depressed, renders all stations inoperable.

A two-way leveling device is provided to maintain floor level.

No controls except the emergency stop will override a control device in operation. Controls on the car have priority and render hall station controls inoperative while the push buttons are depressed and, for a timed period when they are released. Other than the leveling device, all controls are switched off when any door is open. The doors are mechanically locked when the car is not at the landings.

The failure of any single, magnetically operated switch, contactor, or relay to release in the intended manner shall not prevent the car from stopping in response to terminal stopping devices.

A pit switch is provided that when activated removes power from the system for safety during service and maintenance.

Pitless/Rampless Option: Also available, Atlantic Material Lifts with no pit and no ramp.

This NEW concept of Material Lifts is simply anchored to your floor slab. It does not require a ramp or expensive concrete pit work.

This unit can serve two or more landings depending on the travel distance, complete with expanded metal hoistway, double swing doors, and constant pressure push buttons.

Up to 4,000lb. capacity lift speed 30 f.p.m. Built to ASME A17.1 / CSA B44 (elevator codes).

MODEL SFPL MATERIAL LIFT

  • Door closer
  • Hollow metal swing doors
  • Hydraulic cylinder
  • Push button station
  • Solid metal car sides
  • Checker plate deck surface
  • Power unit
  • Controller
  • Disconnect
  • Concrete block hoistway enclosure

MODEL DFPL MATERIAL LIFT

  • Structural frame and expanded metal hoistway enclosure
  • Electro mechanical door interlock
  • Guide rail mast